Black 11º Bends
Black 11º Injection Moulded Electrofusion Spigot Elbows / PN16 / SDR11
Friatec's PE100 RC Injection moulded electrofusion elbows are suitable for fusing pipes from SDR11 to SDR17.6 Electrofusion sockets feature all the same performance benefits found in black couplers. This fitting has an electrofusion socket one end and spigot the other, allowing two elbows to be combined together to provide an adjustable angle from 0º to 22º.
NOTE: The pipe, socket and spigot ends must be prepared in accordance with the general installation instructions using a spigot mechanical peeler, 90% Isopropyl alcohol wipes and we recommend using the Friamat fusion control unit to achieve correct preheating and logging the full range of weld data available.
| Subject to the Engineers approval, this product can be used in above-ground PN16 applications that require PN20 fittings for the purpose of thermal de-ration. Socket fittings do not require thermal de-ration as the fitting is reinforced, due to sockets overlapping the spigots. This statement is only applicable for fittings operating at up to PN16 Maximum Operating Pressure. | ||||||||
|
Product Code |
dn |
D1 |
L |
L1 |
L2 |
le |
Z |
Availability in Hong Kong |
|
P3326.112.125 |
125 |
160 |
250 |
84 |
34 |
87 |
166 |
8-12 Weeks |
|
P3326.112.180 |
180 |
226 |
310 |
100 |
50 |
105 |
210 |
8-12 Weeks |
Black 11º Injection Moulded Spigot Elbows / PN16 / SDR11
Black injection moulded spigot elbows are available in larger sizes up to DN/OD 400, however, these sizes are not listed in our water section as Minimum Order Quantity (MOQ) makes their supply uneconomic. A complete list of black moulded spigot bends can be found in our wastewater section here.
Black 11º Segmented Spigot Bends / PN16 / SDR11
Black fabricated spigot bends are available in all sizes and pressure ratings, however, PN10 and PN16 bends are not listed in our water section, as typically Blue or Purple fabricated bends would be used in hong kong. For above-ground applications requiring thermal de-ration, PN20 / SDR9 black bends would be used. A range of black fabricated spigot bends can be found in our wastewater section here.
Black 11º Segmented Spigot Bends / PN20 / SDR9
PN20 / SDR9 fabricated bends can be used for above-ground installations exposed to direct sunlight in a PN16 pipeline, where the pipes surface temperature may exceed 40ºC. The higher pressure rating allows for thermal de-ration due to prolonged elevated operating temperatures.
Manufactured from Mill-Pro M100 PE100 RC SDR9 Black pipe and fabricated according to BS EN 12201-3, clause B.3, using butt weld techniques according to BS ISO 21307. They feature long spigots for electrofusion or butt fusion joining and 1D and 2D bar code stickers for complete product traceability. All bends are sealed in individual plastic bags for protection on site.
Segmented bends are manufactured from a pipe, with cut angles ≤ 7.5º and therefore are not subject to pressure de-ration factor required in BS EN 12201 Clause B.3. Generally, the internal weld beads are removed where possible and external weld beads are not removed unless ordered otherwise.
Any bend angle from 0º to 15º can be custom manufactured, standard angle for a single mitre bend is 11º with a radius of 2.5 x OD.
NOTE: The spigot ends must be prepared in accordance with the general installation instructions using a spigot mechanical peeler, 90% Isopropyl alcohol wipes.
|
dn800 is the largest size bends available in SDR9. |
|||||
|
Supply of Bends in sizes ≥ dn250 is subject to the availability of SDR9 pipe. |
|||||
|
Product Code |
dn |
le |
r = 2.5 dn |
Z – 11º Single mitre |
Availability in Hong Kong |
|
P5817.290.090 |
90 |
150 |
225 |
172 |
4-6 Weeks |
|
P5817.290.125 |
125 |
150 |
313 |
180 |
4-6 Weeks |
|
P5817.290.180 |
180 |
150 |
450 |
193 |
4-6 Weeks |
|
P5817.290.250 |
250 |
250 |
625 |
310 |
Contact us |
|
P5817.290.315 |
315 |
300 |
788 |
376 |
Contact us |
|
P5817.290.355 |
355 |
300 |
888 |
385 |
Contact us |
|
P5817.290.450 |
450 |
300 |
1125 |
408 |
Contact us |
|
P5817.290.500 |
500 |
350 |
1250 |
470 |
Contact us |
|
P5817.290.560 |
560 |
350 |
1400 |
485 |
Contact us |
|
P5817.290.630 |
630 |
350 |
1575 |
502 |
Contact us |
|
P5817.290.710 |
710 |
350 |
1775 |
521 |
Contact us |
|
P5817.290.800 |
800 |
350 |
2000 |
543 |
Contact us |
Black 11º Fabricated Spigot Elbows / PN10-PN16 / SDR17-SDR11
Fabricated elbows are manufactured from black PE100+ compound. They feature long spigots for electrofusion or butt fusion joining on site. Any fabricated elbow angle from 1º to 45º can be manufactured. Tables below show standard 11º elbow with a radius of ~0.5xOD for reference.
| Custom fabricated elbows do not require pipe to manufacture. Individual elbows may be ordered in any angle. | ||||||
|
PN10 SDR17 |
PN16 SDR11 | d1 | le1 | r | z1 - 11º | Availability in Hong Kong |
| P5314.76.355 | P5316.76.355 | 355 | 200 | 177 | 309 | 14-16 weeks |
| P5314.76.400 | P5316.76.400 | 400 | 300 | 200 | 411 | 14-16 weeks |
| P5314.76.450 | P5316.76.450 | 450 | 300 | 225 | 413 | 14-16 weeks |
| P5314.76.500 | P5316.76.500 | 500 | 300 | 250 | 426 | 14-16 weeks |
| P5314.76.560 | P5316.76.560 | 560 | 300 | 280 | 451 | 14-16 weeks |
| P5314.76.630 | P5316.76.630 | 630 | 300 | 315 | 460 | 14-16 weeks |
| P5314.76.710 | P5316.76.710 | 710 | 500 | 355 | 662 | 14-16 weeks |
| P5314.76.800 | P5316.76.800 | 800 | 500 | 400 | 663 | 14-16 weeks |
| P5314.76.900 | P5316.76.900 | 900 | 500 | 450 | 732 | 14-16 weeks |
| P5314.76.1000 | P5316.76.1000 | 1000 | 500 | 500 | 741 | 14-16 weeks |
| P5314.76.1200 | - | 1200 | 500 | 600 | 709 | 14-16 weeks |
